Setting the Value of the Design Coefficient for A 0.3MPa Gas Supply Use PE Piping System in Japan [PE]

Author(s) : Wang Zhanjie

As the largest production country, with numerous applications, China’s plastic pipe industry is developing steadily to meet the demand and needs. This paper analyzes the current situation and barriers, and proposes the breakthroughs to achieve a sustainable, stable and healthy development of China’s plastic pipe...

Author(s) : Liang Yu, Akshay Ponda, Dane Chang

Following the development of US shale oil and gas production since 2007, the demand for thermoplastic pipes with better corrosion resistance, and lower installation and operation cost than carbon steel pipe, has been growing significantly. Nylon 12 has been qualified for hydrocarbon transportation in offshore flexible...

Author(s) : Mario Messiha, Andreas Frank, Isabelle J. Berger, Jan Heimink, Hermann van Laak, Florian Arbeiter, Gerald Pinter

Since the last decade polyamide 12 (PA12) has been successfully introduced as material for SDR 11 gas piping systems up to 18 bar, representing itself as an attractive alternative to steel pipes for high-pressure applications. Practical experience has confirmed that beside the higher strength, PA12 pipe grades also...

Author(s) : Ryosuke Nagahisa, Shinichi Katoh

We investigated the possibility of using a greaseless polyethylene (PE) ball valve by applying a coating on it to improve the valve’s robustness. In order to verify the valve’s operability, we performed initial-operating-torque, abrasion, and dust tests on both grease-applied and coatingapplied ball valves. These...

Author(s) : HU Fa, LI Yue, GAO Yuanjie, ZHE Dongmei, WEI Ruoqi

This paper expounds the development status of composite insulating pipe in the heating and chemical fields from the aspects of materials, structure and application. Combined with the relevant standards and technical requirements, the performance advantages and the key evaluation methods such as axial shear strength,...

Author(s) : Suleyman Deveci, Birkan Eryigit, Senthil K. Kaliappan

The effect of eccentricity on the failure time of pipes under hydrostatic pressure test has a significant magnitude that it can easily mislead the evaluation of pipes according to requirement of ISO 4427-2. Therefore, authors propose a maximum relative eccentricity limit of 0.015, even lower, for pipes being tested...

Author(s) : Christian Schalich

This paper introduces a new technology based on millimeter waves. It provides a noncontact, non-destructive, online measurement of inner and outer diameter, ovality, wall thicknesses, and sagging (sagging of the melt during solidification at a too high viscosity) of large plastic pipes during the extrusion...

Author(s) : Bülent Kuzkaya

Spiral wound pipes are becoming more and more important in larger diameter HDPE pipe production technology. The spiral wound structured wall pipes with profiles are already well known and used for several low or non-pressure pipe applications. This paper shows that spiral wound pressure pipes can fulfill the...

Author(s) : Richard St-Aubin, Dr. Thomas O’Rourke, Dr. Brad Wham, Blake Berger

Molecularly oriented polyvinyl chloride (PVC-O) pipe has been found to withstand large ground deformation during seismic events without damage. The properties of PVC-O pipe that support this performance have been investigated in a multi-year testing program undertaken at the Geotechnical Lifelines Large Scale Testing...

Author(s) : K. Moita

East Bay Municipal Utility District (District) provides water and wastewater services to the eastern region of the San Francisco Bay Area in California. The District’s potable water system serves approximately 1.4 million customers in a 332-square-mile area that spans portions of Alameda and Contra Costa Counties. The...

Author(s) : Baiqian Li, Jun Wang, Lixian Zheng, Xiaoyi Peng, Lei Wang, Yu Cui, Guozhi Xu

Polyethylene/Aluminum/Polyethylene (PAP) composite pipe has the advantages of corrosion resistance, limited joints and convenient installation. Nowadays PAP pipes are widely used in indoor gas conveyance. But a number of companies encounter difficulties in installing gas meter in users’ house as well as billing. Some...

Author(s) : Zhang Wei, Wei Ruoqi, Zhou Minghong, Zhou Mingwei,

This article gives a brief introduction of plastic inspection chambers in China. It focuses on the formulation of China's national standard for plastic inspection chambers and conducts the theoretical analysis and data validation of the key technical metrics in the standard for the following three tests: the...

Author(s) : Katsutaka Nakagami, Takahiro Kasatani

Osaka Gas improves various approaches to the improvement of polyethylene piping construction quality and executes the approaches. As a result of that, polyethylene pipes in Osaka Gas maintain high-quality and withstand the earthquakes. This paper shows these methods and performance against earthquakes in Japan. In...

Author(s) : Alex Stolarz

THE PE-RT TECHNOLOGY HAS EVOLVED SINCE IT HAS BEEN FIRST INVENTED AND INTRODUCED TO THE MARKET IN 1982. AN ESTABLISHED TECHNOLOGY FOR HOT AND COLD WATER PIPES USED IN DOMESTIC APPLICATIONS HAS POSITIONED ITSELF WELL WITHIN OTHER MATERIALS DUE TO THE COST EFFICIENT PROCESSING, HANDLING AND PRODUCTION OF PIPES. RECENT...

Author(s) : C.B. Dandekar

Plastic Corrugated Piping System (PCPS) was introduced in India in 2001, much later than the western world started using it for various applications. It received a mixed response from the Govt. Agencies, but was well accepted by the market, actual users and standardizing institutions. PCPS finds applications in...

Author(s) : Ian Aldridge, Declan Robinson, Dave Smart, Chris Reed, Martyn, Greig, Trevor Stafford, David Christie-Lowe, Alec Erskine

For the UK polyethylene (PE) gas pipe network, the first installations now exceed 40 years in the ground, with an original design life of 50 years. It was thus timely to review the current condition and performance history of these first generation PE materials. A major 4 year project was started in 2010 to examine...

Author(s) : René Hermkens, Ernst van der Stok, Johannes de Bruin, Jeroen Weller

The replacement of fossil fuels like natural gas by sustainable gases such as biogas and hydrogen can mitigate global warming. There has been some debate about the impact of sustainable gases on the materials used in the gas grid. An extensive study of the behaviour of PE, PVC, POM and rubber materials was therefore...

Author(s) : Carolin Spirinckx, Peter Sejersen, Zoran Davidovski, Karolien Peeters

For the European Plastic Pipes and Fittings Association (TEPPFA) it is important to have an insight into the environmental aspects during the life-span of plastic pipe systems all the way from the cradle to the grave. The result of the studies allows TEPPFA and its member companies to distinct (for the pipe systems...

Author(s) : Vivek Rohatgi, Pamela L. Maeger, Ashish M. Sukhadia

This study is related to two common approaches used for pipe fabrication, viz. in-line compounding and extrusion of a pre-compound. Pipes were extruded using both approaches and properties were evaluated per the relevant ASTM and ISO standards for water and gas pressure pipe applications to compare the performance of...

Author(s) : Hiroto Taguchi, Hideto Kurokawa, Kaori Numata

This study pursued a quantitative evaluation of “the resistance to third party attacks”, whether pipes are destroyed or not, of two polyethylene pipes (PE80 and PE100) and two polyamide12 (PA) pipes. Two types of tests that simulate the impact from actual digging machine (attack simulation test) and four types of the...