Flexible plastic solution for district heating pipes

Author(s) : Márton Bredács, Andreas Frank, Amaia Bastero, Alex Stolarz, Gerald Pinter

Accelerated aging experiments by the immersion of a commercial polyethylene (PE) pipe grade in 10 ppm of chlorine dioxide (ClO2) and in 100 ppm of hypochlorite (HOCl) solution at 60 °C were performed. An additional immersion test was conducted in 1 ppm of ClO2 at 40 °C. The exposure parameters were continuously...

Author(s) : Nolene Byrne, Rasike De Silva, Keith Lenghaus, Tim Hilditch

Plastic pipes have been utilized in the Australian gas distribution network since the early 1970s. The most common plastic type found in Australia is polyethylene (PE), although nylon is extensively used in New South Wales. Early installation of PE pipe was completed using the first generation high density type PE50...

Author(s) : Ignacio Muñoz

During the last years PVC-O has become a popular product in pipe business due to the huge improvements of mechanical properties of PVC after orientation. At the same time, CPVC has become an important choice for hot water conduits in in-house applications. Molecor has started a research program to evaluate the...

Author(s) : Anders Andtbacka, Frans Alferink, Peter Sejersen

The behavior of buried plastic pipes is already well described in standards and technical specifications and as well as proven in real life conditions. Plastics pipes in diameters up to around 400 mm are already in use for more than 60 years and pipes with larger diameters for more than 20 years now. All with good...

Author(s) : Davidovski Zoran

To get a deeper insight in why plastic pipes systems in some cases are deselected by designers, installers and users, European Plastics Pipes and Fittings Association (TEPPFA) initiated a research including interviews in four pilot countries: Poland, France, Germany and the UK. The first phase was concentrating on...

Author(s) : Suleyman Deveci, Birkan Eryigit, Senthil K. Kaliappan

The effect of eccentricity on the failure time of pipes under hydrostatic pressure test has a significant magnitude that it can easily mislead the evaluation of pipes according to requirement of ISO 4427-2. Therefore, authors propose a maximum relative eccentricity limit of 0.015, even lower, for pipes being tested...

Author(s) : Christian Schalich

This paper introduces a new technology based on millimeter waves. It provides a noncontact, non-destructive, online measurement of inner and outer diameter, ovality, wall thicknesses, and sagging (sagging of the melt during solidification at a too high viscosity) of large plastic pipes during the extrusion...

Author(s) : C. B. Dandekar

Agriculture is the major occupation practiced in India, and irrigation is therefore a vital part of the entire water budget of the country. India possesses only 4% of the total world’s fresh water resource, of which, more than 80% is consumed solely in the Agriculture Sector (Dhawan, 2017). Canal based distribution...

Author(s) : Bülent Kuzkaya

Spiral wound pipes are becoming more and more important in larger diameter HDPE pipe production technology. The spiral wound structured wall pipes with profiles are already well known and used for several low or non-pressure pipe applications. This paper shows that spiral wound pressure pipes can fulfill the...

Author(s) : Pavel Hutar, Jan Poduska, Pavol Dlhy, Andreas Frank, Jaroslav Kucera, Jiri Sadilek, Gerald Pinter, Lubos Nahlik

This paper investigates possible use of recycled material as a part of a multilayer polyethylene pressure pipe system. Crack propagation in different configurations is simulated. Lifetimes of pipes containing recycled material are calculated. Results are compared with lifetimes of pipes made of virgin...

Author(s) : Jacob John, Andrew J. Ortquist, Mats Thunwall, Patrik A. Roseen

This study investigates production of crosslinked polyethylene (PEX) pipes using a resin obtained from a renewable resource via twin-screw extruder technology. PEX pipes were extruded using petroleum-based and renewable high-density polyethylene (HDPE) for comparison. Testing using relevant ASTM standards on the new...

Author(s) : J.D. Kim, S. Kim , T. Schmutz, C. Malchaire, D. Scholz, K. Keck

Since a few years, pipe producers are facing the challenge to protect their plastic pipe from degradation due to chlorine dioxide. Unfortunately, most existing stabilization solutions are not effective enough to insure the desired lifetime of the material. This study shows how the latest development allow to top-up...

Author(s) : Robert Lawrence, Mohana Murali

The paper covers the growth of the polyethylene pipe sector in the Middle East from the 90s to the present. The initial slow uptake was related to ignorance of the material properties from the end users through to designers and installers. Recently the Middle East has become a world leader in the use of ever larger...

Author(s) : Ludo Debever, Peter Sejersen, Carolin Spirinckx

Until today there are various ways of demonstrating the Environmental Performance of products, such as Life Cycle Assessments (LCA), Life Cycle Impact Assessments (LCIA), Environmental Performance Declarations (EPDs). The methods to obtain the result, however, can vary from country to country and can be interpreted...

Author(s) : Norbert Jansen, Albert Lueghamer

Demand for polyethylene (PE) pipe continues to grow on a global basis. The performance properties of this tough, durable piping material are widely recognized by the engineering and design community on a worldwide scale and the range of applications expands. The evolutionary trend in PE piping systems has been very...

Author(s) : Alex Stolarz

THE PE-RT TECHNOLOGY HAS EVOLVED SINCE IT HAS BEEN FIRST INVENTED AND INTRODUCED TO THE MARKET IN 1982. AN ESTABLISHED TECHNOLOGY FOR HOT AND COLD WATER PIPES USED IN DOMESTIC APPLICATIONS HAS POSITIONED ITSELF WELL WITHIN OTHER MATERIALS DUE TO THE COST EFFICIENT PROCESSING, HANDLING AND PRODUCTION OF PIPES. RECENT...

Author(s) : Alex Stolarz, Jian Wang

THE PE-RT TECHNOLOGY HAS EVOLVED SINCE IT HAS FIRST BEEN INVENTED 1982. AN ESTABLISHED TECHNOLOGY FOR HOT AND COLD SANITARY PIPES HAS POSITIONED ITSELF WELL WITHIN OTHER MATERIALS DUE TO THE EASY PROCESSING, HANDLING AND COST EFFICIENT PRODUCTION OF PIPES. RECENT TECHNOLOGY ALLOWS EVEN MORE FLEXIBLE RESINS TO BE...

Author(s) : Ian Aldridge, Declan Robinson, Dave Smart, Chris Reed, Martyn, Greig, Trevor Stafford, David Christie-Lowe, Alec Erskine

For the UK polyethylene (PE) gas pipe network, the first installations now exceed 40 years in the ground, with an original design life of 50 years. It was thus timely to review the current condition and performance history of these first generation PE materials. A major 4 year project was started in 2010 to examine...

Author(s) : Aimin Xiang, Jianling Xie, Yuanzhang Yu, Yufeng Ren

PE-UHMW pipes standard and application in China are introduced. In this study, the tensile properties, charpy impact strength and abrasion characteristics of PE-UHMW pipes were investigated. These results demonstrate the excellent properties of PEUHMW pipes. A novel method of testing melt flow rate was also...

Author(s) : Amaia Bastero, Márton Bredács, Andreas Frank

The effect of chlorinated water environment to plastic pipes has been intensively investigated in recent years and proved to affect the lifetime of plastic pipes. Since it is known that the use of the different disinfectants (ClO2, HClO/ClO- ) imply different degradation rates, understanding the conditions...