Our site uses cookies necessary for its proper functioning. To improve your experience, other cookies may be used: you can choose to disable them. This can be changed at any time via the Cookies link at the bottom of the page.


Collection and Recycling of Plastics Pipes in the Demolition and Construction Waste System [PVC, PE]

 

Recycling & Environment

Plastic Pipes Conference Association # 2006 Washington DC

Whittle, Pesudovs

The process of extracting scrap plastics pipes from the demolition and construction waste stream in a major city is described together with a quantification of the proportion of the most common plastics pipe materials in the waste. The condition of the pipes and the methods used to turn them into a re-usable form is described. The pilot trial is now being expanded to recycle pipes in the 3 largest cities in Australia.

Please note that the whole article content is available on PPCA website only :

Related papers

2014 Chicago : Plough-in of Large Diameter Polyethylene Pipes

Author(s) : Alan Whittle, Jim Campbell

The coal seam gas industry in Australia is currently undergoing a major expansion with over 50,000 km or 30,000 mile of PE100 pipes to be installed in diameters ranging from DN110 to DN710. The pipes are being used to carry produced water, gas and treated water. The considerable quantity of pipe to be installed in...

2012 Barcelona : Best environmental practice PVC pipes and fittings for the green building industry

Author(s) : Nigel Jones, George Macovaz, Alan Whittle, and Mark Heathcote

Key Words : PVC, Green Building Until recently the Australian green building rating tool effectively created a disincentive to use PVC pipe. The PVC industry in general and the PVC pipe industry in particular worked with the Green Building Council of Australia (GBCA) and associated stakeholders to establish an...

2012 Barcelona : Performance and sustainability advantages of PVC sewer pipes in australia

Author(s) : Alan Whittle, Nigel Jones and Mark Heathcote

PVC has been used successfully for sewer and sanitary drainage pipes in Australia for over 40 years. It is the predominant material for these applications. The reason for this success is the superior, all round performance of PVC piping systems compared to the various alternatives. Equally important has been the...

2004 Milan : Predicting the Residual Life of PVC Sewer Pipes

Author(s) : Whittle, Tennakoon

Ipswich Water commenced reviewing the service lives of different pipe materials in its gravity sewer system. Unlike other pipe materials, PVC sewers did not have failure histories, or deterioration revealed in CCTV inspections, even after 25 years of service. Therefore establishing a realistic predicted life was not...

2004 Milan : Resistance of PVC-U and PVC-M to Cyclic Fatigue

Author(s) : Whittle, Teo

PVC-U and PVC-M pipes may be used in applications where they are subjected to cyclic pressures generated by the operation of pumps and valves. It is therefore important that the pipe material’s response to cyclic loading is quantified and that pipelines are designed and operated within the material’s established...

2001 Munich : Assessment of the Strength and Toughness of Modified PVC Pipes

Author(s) : Whittle,Burford, Hoffmann

A series of modified PVC pipes, with different concentrations of chlorinated polyethylene, were manufactured under carefully controlled processing conditions. The strength and toughness of each pipe was measured by a variety of methods including uniaxial tensile strength, notched C-ring, essential work of fracture,...

2001 Munich : Elastomeric Pipe Joint Performance Requirements for Use in PVC Sewer Pipelines

Author(s) : Sadler, Burn, Whittle

Root intrusion into sewer pipelines is a major concern, especially in areas with a combination of dry climate and vigorous vegetation growth. For elastomeric pipe joints to resist root intrusion, some national standards specify a minimum interfacial pressure that must be maintained between the elastomeric ring and the...

2001 Munich : Investigating Crack Growth and Plasticity in the C-Ring Fracture Toughness Test

Author(s) : Davis, Burn, Whittle

The C-ring test method is widely used by the water industry to determine the fracture toughness of poly(vinyl chloride) (PVC) pipes. The test currently forms a draft ISO standard (ISO/DIS 11673.2) and an interim Australian/New Zealand Standard (AS/NZS 1462.19(Int)) for fracture toughness assessment. Whilst results...

2001 Munich : Long Term Performance of PVC Pressure Pipes in a Large Rural Water Supply Scheme

Author(s) : Stahmner, Whittle

A number of PVC pressure pipes were exhumed from a large rural water supply scheme constructed in the early 1970s. The pipes had been extruded by three manufacturers in both elastomeric seal and solvent cement joints. The pipes were subjected to a range of mechanical tests in order to assess whether there had been any...

1998 Gothenburg : Elastomeric Joint Comparison of PVC, VC and FCR Pipes

Author(s) : Lu, Burn, Whittle

For rubber ring joints to resist plant root penetration, it has been reported and promulgated into Australian Standards that a sufficiently high contact pressure between the rubber and the pipe must be maintained. The evaluation of the appropriate interfacial pressure to be used has been under discussion for some time...

1998 Gothenburg : Optimising the Performance of Modified PVC for Pressure Pipe Applications

Author(s) : Whittle, Burford)

Modified PVC pipes are being introduced for water reticulation where their tough, predictable behaviour offers advantages in both performance and material utilisation. CPE is one of the modifiers used, either alone or in combination with other additives. The effects of changes in processing conditions on both the...

Fatigue Crack Propagation of PVC-U and PVC-M Pipes in a Water Environment

Author(s) : Samt, Whittle, Hoffman, Burford

Wimmera Mallee Pipeline Project

Author(s) : Whittle, Resenberger, Tan

Members of the Association

BOREALISBOROUGEFormosa Plastics CorporationHanwha TotalEnergiesINEOS O&PIRPCKorea Petrochemical IND. Co., LTD (KPIC)LyondellBasellPetroChina Dushanzi Petrochemical CompanyPRIME POLYMERSABICSCG Chemicals & Thai PolyethyleneSinopecTASNEE
TOP