Our site uses cookies necessary for its proper functioning. To improve your experience, other cookies may be used: you can choose to disable them. This can be changed at any time via the Cookies link at the bottom of the page.


The Use of recently Developed Experimental Methods and Modelling Techniques to study Crack Propagation in Viscoelastic Materials

 

Fracture & Resistance

Plastic Pipes Conference Association # 1992 Eindhoven

Clutton, Dear, Channell

Two novel techniques have been applied to the problem of determining the fracture toughness of polyethylene appropriate to the situation of rapid crack propagation in pipe systems.
Agreement is found between the data from the two methods used for evaluating four grades of polyethylene of widely different toughness. By implication, either technique is valid for determining fracture toughness, but each method has a wider utility depending upon other evaluation requirements.


Increasingly, polyethylene (PE) is being used in water and gas pipeline systems for which the requirements are rigorous and demanding. In particular, there is a need for high fracture toughness both for sustained long term static loading and short term impact loading. As systems grow and pipes of larger diameter and wall thickness are required, the likelihood of brittle failure under plain strain conditions increases. The need for better information about the resistance of materials to this type of rapid crack propagation is essential.

Please note that the whole article content is available on PPCA website only :

Related papers

2004 Milan : Interpretation of the Results of the Full Notch Creep Test and a Comparison with the Notched Pipe Test

Author(s) : Beech, Clutton

Design of pipe systems for lifetimes in excess of 100 years depends on accelerated testing of pipe at different temperatures, and standard extrapolation methods for assessment of the minimum required strength. However resistance to slow crack growth is an essential parameter to take into account for the development of...

2001 Munich : Mechanisms of Slow Crack Growth in PE Pipe Grades

Author(s) : Beech, Ferguson, Clutton

Design of pipe systems for 50 year lifetimes depends on accelerated testing of pipe at different temperatures and standard extrapolation methods for assessment of whether the minimum required strength is achieved. Further acceleration is used in the notched pipe test (NPT), which is a medium term (up to 1000 hour)...

1998 Gothenburg : Slow Crack Growth and Impact Mechanisms in PE

Author(s) : Clutton, Rose, Capaccio

The development of pipe grades requires the careful balance of several mechanical properties, of which two of the most important are the resistance to slow crack growth (SCG) and rapid crack propagation (RCP). In this paper, we present small-scale tests which enable the rapid assessment of these properties. These...

1995 Edinburgh : Assessing mechanical properties of polymers for pipe application

Author(s) : Dear, Brown, Mason

The threshold load to just maintain crack propagation and conditions for catastrophic failure, should the material be loaded above this threshold, are two key evaluation requirements when assessing polymers for pipe applications. Often these assessments need to be made during material research and development and...

1995 Edinburgh : Prediction of Notched Pipe Stress Crack Performance

Author(s) : Rose, Channell, Palmer

A series of PE 80 and PE 100 materials have been investigated to determine whether there exists a link between resistance to slow crack growth as measured by notched pipe test and creep of macroscopic oriented samples. Preliminary results suggests that there is a correlation between a single creep parameter and...

1995 Edinburgh : The Role of Crazing in the Impact Fracture Toughness of PE Pipe Grades

Author(s) : Channell, Clutton

A new method based on the Dugdale zone solution for finite geometries is presented to analyse the case of craze growth at the notch tip in Charpy impact experiments. It is believed that correct values of initiation toughness are calculated via this method, leading to greater confidence in the extrapolation technique...

1992 Eindhoven : Fibre Creep and Long-Term Fracture Resistance in PE

Author(s) : Channell, Cawood, Capaccio

A critical appraisal has been carried out of the creep fracture of the fibrils in the pre-crack damage zone (craze) of polyethylene homo and copolymers. It has been shown that by assuming that the fibrils are drawn to the natural draw ratio of the material, a clear correlation can be established between the creep rate...

Members of the Association

BOREALISBOROUGEFormosa Plastics CorporationHanwha TotalEnergiesINEOS O&PIRPCKorea Petrochemical IND. Co., LTD (KPIC)LyondellBasellPetroChina Dushanzi Petrochemical CompanyPRIME POLYMERSABICSCG Chemicals & Thai PolyethyleneSinopecTASNEE
TOP